If you own a Ford truck equipped with a backup camera and find yourself in a situation where you need to remove the tailgate, you might wonder how to do it without affecting the camera’s functionality.
The process of removing a Ford tailgate with a backup camera can be a bit daunting if you’re not familiar with it, but fear not – it can be done with relative ease if you follow the right steps.
Easy Tailgate With Camera Removal
Here are a few quick tips:
My idea is to post this since I’ve seen a lot of complaints about removing the tailgate with the camera being such a hassle.
In addition to spraying bed liners at my job, I also take one of these gates off every other day (roughly). I take less than a minute to do it.
If you crawl under the truck, you’ll see a clip holding the wiring harness in place. Unclip it. You will find it just after the gate if you don’t know which one to follow.
Simply unplug the harness after that.
Now, leave the gate open. Make sure you don’t drop the gate. The harness can be found behind the bumper and between the gate and the bumper.
Feed it through here. When the gate is up, this is the easiest way to do it. I have found that to be the case, at least.
And you’re here.
You can now remove the tailgate as usual. Getting a helper is a good idea if you have one with a man step. I hate how heavy and awkward they are.
How To Remove A Tailgate With A Backup Camera On F-250?
The following steps will show you how to remove the tailgate and camera from your Ford F-250.
A big part of the F-250’s job is hauling heavy cargo and equipment, so the vehicle is built for heavy work. The tailgate needs to be removed from time to time to gain access to more cargo space.
Moreover, removing the tailgate will simplify the installation of equipment on your F-250’s bed if you plan to permanently mount it.
1. Getting Your Truck Ready
- Make sure your F-250 is parked on a level surface.
- Put the parking brakes on.
- Put your transmission in Park (P).
- Check if you can still slide under your F-250 with modified wheels and tires without jacking it up if you made some modifications.
Here are the steps you need to follow if you need to jack it up. You can skip to the next section if you don’t need it.
- The tires opposite the one you will jack up should be chocked with tire chocks. The two front tires should be chocked in this case.
- The floor jack should be positioned under your F-250.
- The recommended jack-up points on your F-250 must be used.
- The jack-up point on your F-250 should be supported by a jack stand.
- The other rear tire should be jack-strung and placed under a jack stand. The second jack stand should be level with the first.
- After lowering the floor jack, raise it again just barely touching the jack-up point. If your jack stand fails, you can use your floor jack as a backup.
- Make sure your F-250 is stable enough on the jack stands by tugging at it.
2. You’re About To Go Under Your F-250
- Slide under your truck with a creeper.
- Follow the wire that comes from the tailgate. In the wheel well on the left side, there is a wire harness connector.
- The wire connector can be disconnected by releasing the lock.
- The underside of some F-250 models can have as many as three wire connectors you need to disconnect.
- Near the wire connector that goes to the front of some Ford F-250 models is a terminal cover that is brightly colored.
- This cover needs to be cleaned inside and out.
- You can use the cover to cover an open connector once it’s cleaned so water, dirt, or mud won’t get into it.
- A F-250 with an open connector may experience electrical problems.
- Check your glove compartment if you don’t have the terminal cover hanging on the wire harness.
- The tailgate removal kit inside the glove compartment of some F-250 models includes covers for the wires when you remove the tailgate.
3. Removing The Tailgate
- Your Ford F-250’s tailgate should be opened but not completely lowered. The tailgate should rest on your leg rather than the ground.
- You can unlock the tailgate by pulling the locking clip at the end of the cable with a flathead screwdriver. The tailgate is held parallel to the ground by these steel cables.
- You can release the screw head by pulling the locking clip higher than the level of the support screw. Push the metal cable upward until the screw head reaches the part of the hole that is large enough for it to be released.
- Removing the second steel cable requires the same procedure.
- The tailgate should be angled at around 45 degrees.
- As it can be cumbersome to support the tailgate, it would be best to have a friend assist you.
- Unless a second person is present to support the tailgate’s weight, it may easily slip and fall once it is out of its hinges.
- Remove the tailgate hinge on the right side.
- Make sure the tailgate is at an angle of about 80 degrees with the ground. During the next step, make sure you’re prepared to support the entire weight of the tailgate.
- The left side of the tailgate should be out of the left hinge as you slide it to the right.
- Put your tailgate aside.
Ford F-250: How To Replace The Backing Camera?
A Super Duty truck’s tailgate is subjected to a lot of abuse. Cargo hauled on the bed of your truck will be required to go over the tailgate unless the tailgate is removed first.
You can’t remove the tailgate of your truck every time you need to load cargo on its bed and then reinstall it again. After you unload all of your cargo, you won’t be able to just remove the tailgate once again and replace it once you reach your destination. I don’t think that’s feasible.
Also subject to abuse is the backing camera on the tailgate of your F-250. It will eventually take its toll on the camera when you load and unload cargo from your truck’s bed.
It is also possible for moisture to get into the backing camera of your F-250 truck after power washing it. Your camera’s image can be blurred by this moisture.
That’s why this article is here to help.
The following steps will show you how to replace the camera on your Super Duty Ford F-250 truck.
Getting Access To The Old Camera
- Make sure you park your truck on a level surface that has plenty of light.
- You can follow steps 2 and 3 from the section above on “Getting Your Truck Ready”.
- The tailgate should be opened.
- The tailgate step can be released by pressing the button in the middle of the molding.
- The bolts under the step can be accessed by pulling the step.
- The handle is held in place by four nuts. Remove these nuts.
- Pull the tailgate handle horizontally and close the tailgate. Keeping the handle in place should only be done with plastic clips.
- The camera cover is held in place by a Torx screw. Remove it.
Replacing The Camera
- Take the old camera off the wall and disconnect the wires.
- The old camera should be removed from the mounting.
- The new camera should be installed.
- The new camera should be connected to the wire harness.
- The camera cover should be reinstalled.
- The Torx screw should be used to secure the camera cover.
Finishing Up
- The handle for the tailgate should be reinserted.
- Make sure the tailgate step is partially deployed when you reopen the tailgate.
- The nuts that hold the tailgate handle in place need to be reinstalled.
- Try out the new camera.
Final Thoughts
Ford designed the tailgate to be easily removed with a backing camera, making it simple to remove the tailgate with a backing camera.
How To Remove Ford Tailgate With Backup Camera?
If you own a Ford truck equipped with a backup camera and find yourself in a situation where you need to remove the tailgate, you might wonder how to do it without affecting the camera’s functionality.
The process of removing a Ford tailgate with a backup camera can be a bit daunting if you’re not familiar with it, but fear not – it can be done with relative ease if you follow the right steps.
Easy Tailgate With Camera Removal
Here are a few quick tips:
My idea is to post this since I’ve seen a lot of complaints about removing the tailgate with the camera being such a hassle.
In addition to spraying bed liners at my job, I also take one of these gates off every other day (roughly). I take less than a minute to do it.
If you crawl under the truck, you’ll see a clip holding the wiring harness in place. Unclip it. You will find it just after the gate if you don’t know which one to follow.
Simply unplug the harness after that.
Now, leave the gate open. Make sure you don’t drop the gate. The harness can be found behind the bumper and between the gate and the bumper.
Feed it through here. When the gate is up, this is the easiest way to do it. I have found that to be the case, at least.
And you’re here.
You can now remove the tailgate as usual. Getting a helper is a good idea if you have one with a man step. I hate how heavy and awkward they are.
How To Remove A Tailgate With A Backup Camera On F-250?
The following steps will show you how to remove the tailgate and camera from your Ford F-250.
A big part of the F-250’s job is hauling heavy cargo and equipment, so the vehicle is built for heavy work. The tailgate needs to be removed from time to time to gain access to more cargo space.
Moreover, removing the tailgate will simplify the installation of equipment on your F-250’s bed if you plan to permanently mount it.
1. Getting Your Truck Ready
- Make sure your F-250 is parked on a level surface.
- Put the parking brakes on.
- Put your transmission in Park (P).
- Check if you can still slide under your F-250 with modified wheels and tires without jacking it up if you made some modifications.
Here are the steps you need to follow if you need to jack it up. You can skip to the next section if you don’t need it.
- The tires opposite the one you will jack up should be chocked with tire chocks. The two front tires should be chocked in this case.
- The floor jack should be positioned under your F-250.
- The recommended jack-up points on your F-250 must be used.
- The jack-up point on your F-250 should be supported by a jack stand.
- The other rear tire should be jack-strung and placed under a jack stand. The second jack stand should be level with the first.
- After lowering the floor jack, raise it again just barely touching the jack-up point. If your jack stand fails, you can use your floor jack as a backup.
- Make sure your F-250 is stable enough on the jack stands by tugging at it.
2. You’re About To Go Under Your F-250
- Slide under your truck with a creeper.
- Follow the wire that comes from the tailgate. In the wheel well on the left side, there is a wire harness connector.
- The wire connector can be disconnected by releasing the lock.
- The underside of some F-250 models can have as many as three wire connectors you need to disconnect.
- Near the wire connector that goes to the front of some Ford F-250 models is a terminal cover that is brightly colored.
- This cover needs to be cleaned inside and out.
- You can use the cover to cover an open connector once it’s cleaned so water, dirt, or mud won’t get into it.
- A F-250 with an open connector may experience electrical problems.
- Check your glove compartment if you don’t have the terminal cover hanging on the wire harness.
- The tailgate removal kit inside the glove compartment of some F-250 models includes covers for the wires when you remove the tailgate.
3. Removing The Tailgate
- Your Ford F-250’s tailgate should be opened but not completely lowered. The tailgate should rest on your leg rather than the ground.
- You can unlock the tailgate by pulling the locking clip at the end of the cable with a flathead screwdriver. The tailgate is held parallel to the ground by these steel cables.
- You can release the screw head by pulling the locking clip higher than the level of the support screw. Push the metal cable upward until the screw head reaches the part of the hole that is large enough for it to be released.
- Removing the second steel cable requires the same procedure.
- The tailgate should be angled at around 45 degrees.
- As it can be cumbersome to support the tailgate, it would be best to have a friend assist you.
- Unless a second person is present to support the tailgate’s weight, it may easily slip and fall once it is out of its hinges.
- Remove the tailgate hinge on the right side.
- Make sure the tailgate is at an angle of about 80 degrees with the ground. During the next step, make sure you’re prepared to support the entire weight of the tailgate.
- The left side of the tailgate should be out of the left hinge as you slide it to the right.
- Put your tailgate aside.
Ford F-250: How To Replace The Backing Camera?
A Super Duty truck’s tailgate is subjected to a lot of abuse. Cargo hauled on the bed of your truck will be required to go over the tailgate unless the tailgate is removed first.
You can’t remove the tailgate of your truck every time you need to load cargo on its bed and then reinstall it again. After you unload all of your cargo, you won’t be able to just remove the tailgate once again and replace it once you reach your destination. I don’t think that’s feasible.
Also subject to abuse is the backing camera on the tailgate of your F-250. It will eventually take its toll on the camera when you load and unload cargo from your truck’s bed.
It is also possible for moisture to get into the backing camera of your F-250 truck after power washing it. Your camera’s image can be blurred by this moisture.
That’s why this article is here to help.
The following steps will show you how to replace the camera on your Super Duty Ford F-250 truck.
Getting Access To The Old Camera
- Make sure you park your truck on a level surface that has plenty of light.
- You can follow steps 2 and 3 from the section above on “Getting Your Truck Ready”.
- The tailgate should be opened.
- The tailgate step can be released by pressing the button in the middle of the molding.
- The bolts under the step can be accessed by pulling the step.
- The handle is held in place by four nuts. Remove these nuts.
- Pull the tailgate handle horizontally and close the tailgate. Keeping the handle in place should only be done with plastic clips.
- The camera cover is held in place by a Torx screw. Remove it.
Replacing The Camera
- Take the old camera off the wall and disconnect the wires.
- The old camera should be removed from the mounting.
- The new camera should be installed.
- The new camera should be connected to the wire harness.
- The camera cover should be reinstalled.
- The Torx screw should be used to secure the camera cover.
Finishing Up
- The handle for the tailgate should be reinserted.
- Make sure the tailgate step is partially deployed when you reopen the tailgate.
- The nuts that hold the tailgate handle in place need to be reinstalled.
- Try out the new camera.
Final Thoughts
Ford designed the tailgate to be easily removed with a backing camera, making it simple to remove the tailgate with a backing camera.